|
| |
FAAC Model 844 Slide
Gate Operator
FAAC is the undisputed world leader in automated gate
opener systems for opening gates, doors and garage doors.
In 1965 FAAC introduced hydraulics in the automatic gate openers sector and,
through the years, has perfected this technology and adapted it to a
multiplicity of needs.
In the 1980’s, FAAC began producing its own electronic equipment, including
access control devices, radio controls, safety and signaling systems. They
were the first to use microprocessors in control units, SMT technology, as well
as simplified self-learning radio controls for electric gate openers.
| MODEL
844 LIMITED DUTY INDUSTRIAL SLIDE GATE OPERATORS |
 
 
Model 844 Slide Gate Operator
Installation
Manual
THE MODEL 844 designed for limited duty industrial
applications. Available in chain and rack&pinion versions. Model 844
has 2 year limited warranty
MODEL 844 CHAIN KITS INCLUDE: Operator Control panel (844
MPS) Sprocket Idlers and protective cover Easy install limit switch plates
Mounting angle brackets Chain-to-gate mounting hardware with nickel plated
master links Chain is not included
MODEL 844 RACK & PINION KITS INCLUDE: Operator Control panel
(844 MPS) Pinion Mounting angle bracket Limit Switch plates
- 230 VAC
- External limits
- Manual release (non-keyed)
- “Soft Stop” on opening and closing
- 3/4 hp motor
- Oil immersed clutch which, when properly
adjusted,
limits the amount of pressure the operator can apply to moving the
gate.
- Duty Cycle: 30% motor run time
- Microprocessor control:
Choose from 4 operating modes:
- signal to open, signal to close
- automatic logic
- security logic
- S2 security logic
|
|
MODEL 844 SLIDE
GATE OPERATOR WITH OIL IMMERSED CLUTCH KITS
|
| MODEL |
PART
NUMBER
|
TYPE |
PULLING
FORCE |
SPEED |
|
844
Z16
(16 tooth sprocket) |
844
M2CO-NP-16 |
CHAIN
(not included) |
125
lbs |
40
ft/min |
|
844
Z20
(20 tooth sprocket) |
844
M2CO-NP-20 |
CHAIN
(not included) |
125
lbs. |
50
ft/min |
|
844
Z16
(16 tooth sprocket) |
844
M2RO-NK-16 |
RACK
& PINION
(not included) |
125
lbs |
40
ft/min |
|
844
Z20
(20 tooth sprocket) |
844
M2RO-NK-20 |
RACK
& PINION
(not included) |
125
lbs. |
50
ft/min |
|
| Maximum
Gate Length is limited by the Pulling Force requirement and the 844's
maximum motor run time of four minutes |
MODEL
844 INSTALLATION KITS FOR CHAIN AND RACK & PINION OPERATORS-
If your operator has a rack & pinion drive, do you want a pedestal or
foundation plate? Refer to the proper kit description below for you
installation |
| PART
NUMBER |
DESCRIPTION |
|
| FAAC3501 |
Slide
Installation Kit with Pedestal for chain operators include- 30ft
nickel plated chain, mounting pedestal, NEMA4 fiberglass enclose with
backplate and power switch, hardware set for enclosure-to-pedestal
attachment, 2 sets of conduit and connectors for conducting enclosure to
operator, 2 caution signs |
|
| FAAC35S1 |
Slide
Installation Kit with Pedestal for chain operators include- same
as above but with 30ft stainless steel chain |
|
| FAAC3503 |
Slide
Installation Kit with Pedestal for rack & pinion operators include-
23ft gear rack, mounting pedestal, NEMA4 fiberglass enclosure-to-pedestal
attachment, 2 sets of conduit and connectors for connection enclosure to
operator, 2 caution signs |
|
| FAAC3512 |
Slide
Installation Kit with Foundation Kit for rack & pinion operators
include- 23ft gear rack, foundation plate, NEMA4 fiberglass
enclosure-to-pedestal attachment, 2 caution signs |
|
| ACCESSORIES
FOR MODEL 844 SLIDE OPERATORS |
| PART
NUMBER |
PART
NUMBER |
|
| FAAC2000 |
Nickel
Plated Chain - #40 nickel plated chain, comes with two master
links with each length of chain you order |
|
| FAAC2002 |
Stainless
Steel Plated Chain - you receive two master links with each
length of chain you order |
|
| FAACCTG01 |
Chain-to-Gate
Mounting Hardware - the hardware needed to attach the two ends of
nickel plated chain to the gate. Includes 2 mounting brackets, 2 tension
bolts and 2 master links (all nickel plated) |
|
| FAACCTGS1 |
Chain-to-Gate
Mounting Hardware - the hardware needed to attach the two ends of
stainless steel plated chain to the gate. Includes 2 mounting brackets, 2
tension bolts and 2 master links (all stainless steel plated) |
|
| FAAC719323 |
Gear
Rack - the galvanized steel rack section measures 3.28ft long and
works with any FAAC slide gate operators. Supplied with rack-to-gate
hardware |
|
| FAAC2278 |
Foundation
Plate (for ground level mounting) - the plate measures 6 x 10.5
in. and has rebar anchors to be set in the concrete pad |
|
| FAAC2411 |
Mounting
Pedestal (for elevated mounting) - 18 in. galvanized mounting
pedestal |
|
|
